• English
  • Global reach with local presence

     

    Unibar 250+

    Grade Colour Code: White 
    Grey/Flake Iron

    Comparative Specification:

    • EN-GJL-250C according to DIN EN 16482
    • EN-GJL-250 according to BS EN 1561 (2011)

    Unibar 250+ has a pearlitic structure (70-90% depending on the diameter), with a ferritic rim, indicated in DIN EN 16482.

    By optimisation of the critical processes and the full absence of carbides in the rim, this quality has excellent machinability and excellent surface finish. The material satisfies mechanical characteristics indicated, with hardness values of 215 HB max, lower than the ones of standard Unibar 250.

    Profile and Size Range

    Standard cut length of our cast iron products is 3080mm, other lengths available on request.

    RoundSquareRectangleSpecial Profiles
    25mm – 360mm25mm x 25mm – 260mm x 260mmUp to 320mm x 220mmSizes and profiles to customer design available on request

    Mechanical Properties

    Material Section mmTensile Strength
    N/mm²
    Hardness
    (BHN)
    Matrix
    20 < D ≤ 50195175 - 215Pearlitic - Ferritic
      50 < D ≤ 100180
    100 < D ≤ 200165
    200 < D ≤ 360155

    Microstructure

    Contains type ‘A’ graphite flakes in accordance with ISO 945. The rim contains fine type ‘D‘ and ‘E‘ interdendritic graphite. The matrix (core) is greater than 70% pearlitic. The rim is predominantly ferritic.

    Ancillary Processes

    Both, our foundries and our local distribution centres offer various services to deliver pre-machined products to our customers. Pre-machined Unibar material will save valuable production time, improve the cost effectiveness and eliminate waste in your own production, allowing you to focus on the key design elements of your products.

    Cutting

    Cutting to specified length in quantities as little as one piece to large volumes, prepared to meet the requirement of your automatic machining systems.

    Turning

    Turning of round bars to required size to meet specific requirements and to minimise the machining operations of our customers. Unibar turned therefore comes with a standard tolerance of +1mm, although after consultation we can offer alternatives to suit all of our customers‘ requirements.

    Milling

    Single and duplex machines offer milling of square and rectangular bars to specified dimensions and agreed tolerances. We can offer our customers milling on either four or six faces for further processing.

    Peeling

    In the case of machined Unibar with diameters of less than 110mm as an alternative to Unibar turned we can offer Unibar peeled by peeling off the oxidised surface layer of the cast bar. As these are smaller dimensions and involve a different machining process, the tolerances offered are more precise, for example h11.

    Boring

    Longitudinal boring as deep as 1000mm is possible by using single head boring and trepanning machines. Unibar tubes can be supplied with the exterior surface as-cast or machined. These two variants can be complemented by a wide selection of internal measurements, which can range from 30mm to 500mm.

    Dimensional Tolerances (Grey/Flake)

    Round
    (As-Cast Diameter mm)
    Ovality Allowances
    mm
    Max. Swell Allowances mm
    20 < (D OR B) ≤ 50-5
      50 < (D OR B) ≤ 10017
    100 < (D OR B) ≤ 200210
    200 < (D OR B) ≤ 300412
    300 < (D OR B) ≤ 400515
    > 400By agreementBy agreement

    Machining Allowances (Grey/Flake)

    Section
    (D Diameter, B Width)
    Min. Machining Allowance mm (per side)
    Round Square/Rectangle
    20 < (D OR B) ≤ 5022.5
      50 < (D OR B) ≤ 10033.5
    100 < (D OR B) ≤ 20044.5
    200 < (D OR B) ≤ 30066.5
    300 < (D OR B) ≤ 40077.5
    400 < (D OR B) ≤ 50099.5
    500 < (D OR B) ≤ 6501111.5

    For rectangular bars the width is the longer dimension of the cross section. Machining allowances of our continuously cast iron bars can be adjusted to meet customer requirements, subject to discussion, prior agreement and special order. For further information please contact our nearest distribution centre.

    Applications

    Our grey iron Unibar 250+ is ideal for an exceptionally wide range of applications. Because of its structure and the mechanical properties it is suitable for the processing within the automotive and glass industries as well as for various applications in the hydraulic and pneumatic section, the machinery and machine tool industry and for pumps and compressors.

    In many ways, Unibar 250+ has a lot of advantages to compete with other materials such as steel, aluminium or the traditional sand casting.

    Advantages:

    • Improved machinability
    • Excellent surface finish
    • 10% weight reduction against steel
    • Excellent vibration damping
    • Faster turning and grinding times
    • Finer grain structure than with sand casting
    • Absence of sand inclusions or cast dimensional problems
    • Elimination of costly patterns
    • Availability from stock

    Do you need any further information about our continuously cast iron products? You will find the appropriate data sheets as well as our technical manual in our download section.

    To find out whether Unibar 250+ is available in your required size, please have a look at our online stock list. Register and keep track of the currently available quantities.